Top 10 typical forklift mishaps ， forklift operation ought to take note of these matters ！.

Don't ignore the forklift at the workplace. If the procedure is not good, there will be serious mishaps in minutes, and there are numerous mishaps including forklifts.

Situation 1: The forklift freight obstructed the motorist's view, and the individual in front might not be discovered, leading to a rolling accident.
Case 2: In order to maintain the balance of the forklift when raising hefty items, the employees used their body weight as the counterweight, which practically caused casualties.
Case 3: The width of the forklift freight goes beyond the allowed size of the path and hangs on the roadside shelf, which almost creates an crash.
Situation 4: Forklift is speeding and rolls over throughout a turn.
Instance 5: The forklift motorist did not observe the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the workers illegally, the forklift driver does not wear the safety belt, the forklift lifter falls and the driver is squashed when the forklift surrender.
Case 7: The forklift vehicle driver did not put on a seat belt and fell from the lorry when it rolled over and was squashed.
Forklift procedure ought to pay attention to these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after confirming that there are no barriers that impede the safety and security of driving, beep the horn first and afterwards start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress ( atmospheric pressure) gauge need to be safe prior to starting.
3. When the forklift begins with a load, the vehicle driver ought to initially verify that the lots is steady and dependable.
4. The beginning should be slow-moving and stable.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the mast ought to be slanted backward. .
2. Do not raise the fork expensive when driving. When going into and leaving the work site or while driving, beware that there will certainly be no obstacles in the sky. When the lots is traveling, the fork should not be elevated too high, which will impact the security of the forklift. .
3. After unloading, the fork must be decreased to the normal driving setting before driving. .
4. When transforming, if there are pedestrians or lorries nearby, the driving signal ought to be released initially. High-speed sharp turns are restricted. High-speed doglegs will certainly create the vehicle to lose lateral security and topple. .
5. When the forklift is downhill, it is purely forbidden to turn off the flame and slide, and it is prohibited to brake instantly while driving with lots unless there are unique situations.
6. When the forklift is running, it needs to comply with the traffic rules in the factory and must keep a specific security distance from the automobile ahead. .
7. When the forklift is running, the lots has to remain in the most affordable placement that does not prevent the driving, and the gantry needs to be effectively slanted back. The lots will not be elevated other than when piling or filling. .
8. The elevation of the tons need to not block the chauffeur's sight. In special circumstances, when the item affects the forward vision, drive at a reduced rate when turning around.
9. It is restricted to activate the ramp, neither to drive across the ramp. .
10. The safe driving speed of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive safely at a low Electric Forklift Truck for Warehouse speed when entering the manufacturing workshop location. .
11. When the forklift is lifted, lifted or driven, it is forbidden for personnel to depend on the fork to hold things and play a stabilizing function. .
12. If issues are discovered, they will be repaired and reported in a prompt way, and they will never operate with illnesses or hide them.

filling and discharging.
1. When fork-loading items, the range between the two forks need to be changed as needed to make the lots of the two forks well balanced and not manipulated, and one side of the item need to protest the rack. .
2. It is restricted to deal with a solitary fork or utilize a fork top or pull. In unique situations, safety and security indication must be established to remind bordering pedestrians. .
3. In the process of loading and dumping products, the forklift must be braked with the brake. .
4. The rate of the car should be sluggish and steady. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled things and hurt individuals. .
5. When using a fork to fork the goods, the fork must be as deep as possible under the tons, and it should be noted that the fork pointer ought to not touch various other goods or items. The load must be maintained with very little back tilt of the gantry to make sure that the load does not slide in reverse. The pole can be tilted ahead a little when the load is reduced to permit easy placement of the lots and removal of the forks. .
6. It is forbidden to fork products at broadband and collide with difficult things with the fork head. .
7. When the forklift is working, it is forbidden for people to loaf the fork, so regarding avoid the collapse of the goods and harm individuals. .
8. Straining is prohibited, and it is restricted to utilize forks to raise employees to engage in high-altitude operations to prevent high-altitude dropping crashes. .
9. It is not allowed to use the brake inertia to slide, place, round or roll items. .
10. It is not permitted to make use of forks to select, transform pallet unload.

Leaving .
1. It is forbidden to leave the forklift when the products on the fork are in the air. Before leaving the forklift, you should discharge the goods or lower the fork framework.
2. Draw the emergency brake manage to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the vehicle's line of sight and does not exceed 1 minute).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the appearance ought to be inspected, and fuel, lubricating oil and air conditioning water need to be included.
2. Examine the security performance of starting, running and braking.
3. Examine whether the lights and horn signals are full and efficient.
4. During the operation of the forklift, check whether the stress and temperature level are typical.
5. After the forklift is running, the external leakage needs to additionally be inspected and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine prior to leaving the automobile;.
2. When you experience someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the cargo need to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming must not be too sharp to stop the propensity of "free switching";.
6. Running up and down the incline must be slow and consistent, and no switching on the slope is enabled.
7. Do not drive across the slope. When the gradient is more than 10%, the automobile should be driven in reverse when going downhill;.
8. When the forklift employees carry the goods and move on, if they experience huge or heavy items and go to the vehicle driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork operation is not permitted.
2. It is not permitted to lift the goods for far away driving.
3. It is not permitted to get the goods by passing on the pallet with the fork.
4. It is not allowed to straight shovel chemicals, flammables and various other dangerous chemicals with forks.
5. It is not permitted to use inertia force to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll items.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is Electric Forklift Truck for Warehouse strictly restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on slopes
.
Parking is not permitted under the list below problems.
1. Contours, slim roads, railway crossings;.
2. Sections with a longitudinal slope more than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the barrier need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844